http://www.corlissnelsonwoodworks

Cello Neck Replacement

I'm in the process of replacing the neck of this cello for my brother.  This is the instrument he played when he was young.

 

I didn't take a picture of it, but I decided to drill small holes at the base of the tenon show here, create a shallow mortice and insert a new maple button for the disfigured and broken existing button.  It was in too bad shape (broken in half and disfigured) to use. The maple insert was around four inches long and the width of the button (under 30mm).  I chose this method rather than removing the back, which I felt was ill advised. I created the illusion of a center seam going through the button.

 

 

There was a significant base bar crack on the top.  I decided to remove the base bar and attach four cleats to the crack.

 

 

Finally I was able to get to the neck replacement!  I'm still working on refining the shape of the neck. 

 

 

 

Cello Shots

Robby's Fiddle Restoration

Singer/Songwriter and good friend, Robby, received this violin from a relative. I offered to fix some of the problems it had including a shiney lacquer on the fingerboard that had areas of a chipped finish among other problems. The back had come unglued at the bottom block leaving a gap that needed to be closed. The bridge had been poorly fitted, was warped and needed to be replaced. The strings were old, dirty and oxidized.

The violin is old but has no label inside. It is an inexpensive instrument but has pretty darn good tone and would make someone happy to play. There is no ebony anywhere on this instrument. It does have blocks and linings and a well fashioned scroll. I had fun bring this instrument back to use again.

My Daughter

On August 15, 2010 my daughter, Holly went missing while on a pontoon boat with her friends at work.  10 days later her body was found in the general area of where she was last seen.  This has been and continues to be a very difficult time for me, my wife and daughter.  We miss our youngest daughter very much and struggle every day with a range of emotions.  We are people of faith and take comfort in the promises of God in our lives here on earth and the life beyond.  Please keep us in your prayers.

Violin Maker's Shop

Recently I visited Chicago with some very dear friends.  I knew this gentleman had a violin shop there and called to see if I might visit briefly.  He was very gracious with his time and talent.  Michael Darnton is a very accomplished violin maker with whom I came in contact through an online violin making forum.  He has been a regular contributor to the forum and has been very helpful to me (and many others) regarding violin making.  While there I witnessed him carve and fit a new bridge on a viola for a member of the Chicago Symphony.  A very valuable lesson indeed!  I took this snap of him before I left.

Jimmy's Violin Restoration

This very old violin was owed by Jimmy's wife's mother, who received it from her father when she was a young girl.  It is a Czechoslovakian Antonio Stradivarius copy. 
When I received this violin, it was in very poor condition. The rib seams at the area of the end block were wide open having come loose from the top and bottom plates.  Several other areas of the top and bottom plates had open seams.  The end pin was half out of the violin and was bent in the shape of macaroni.  It had bent the rib up and away from the belly and back plates because the strings were still on the violin with significant tension on them.  The end block had completely separated from the top and bottom plates and was only held by the ribs.  The violin had a bent bridge - another indication that the it must have experienced significant humidity and heat to be in this shape.  It appeared to have been hung on a wall because it had a ribbon attached to the fingerboard that was used to hang it up.  The fingerboard was not ebony and had serious grooves from many years of playing. The sound post was missing.  I enjoyed bring this fiddle back to life so that it could continue to be passed from generation to generation as a playable instrument.

 
 
 
 

 
 
 

The Final Violin

On April 24, 2010 I finished this violin.  I hope to finish another one by the end of this year between other repairs.

v

Violin Front and Back with Color

William & Mary Style Drop Leaf Table Restoration

I recently finished restoring this drop leaf table. My wife and I bought it at an antique store. It was missing one of the gate leg assemblies (two horizontal spindles and the gate leg.  I turned new spindles and refinished the entire table.  I am now in the process of selling it.  It was a fun little project.